11/07/2012

After complete soldering process, the PIC board is tested on its vibration sensor, relay and LED to make sure it's well-function. The test is conducted using PIC C compiler software. Before the PIC board is test, coding must be done. The test is conducted to test: 

i. light led
ii. blinking led
iii. vibrator sensor and
iv. display  on LCD by activate relay.


The Result:

Then, we were given new task. Encik Mazran ask us to study AP command. Below are the flow:

GSM modem is specialized type of modem that operates over subscription based wireless networks which is similar to a mobile phone. A GSM modem accepts a SIM card, and basically acts like a mobile phone for the computer. Traditional modem is attached to computers for ‘dial-up’ to connect with other computer systems. A GSM modem operates in a similar fashion, except that it sends and receives data through radio waves rather than a telephone line.

Besides the dial-up connection, GSM modem can also be used for sending and receiving SMS which is also one of the key features of GSM modem. In this issue, we discuss on how to set up a simple home automation where we can control the fan and monitor the alarm status by using SMS. All the examples given are based on the MOD 9001D GSM Modem available from Cytron Technologies.Some of the features of this GSM Modem are as follow:


i. RS-232 Interface 
ii. Support PDU and Text mode for SMS 
iii. Tri-Band: GSM900, GSM1800 and GSM1900 
iv. Support TCP/IP 
v.  Support GPRS class 10 
vi. Support standard extended open AT commands 
vii. Accept supply voltage from 5 to 12V 

10/07/2012

Assalamualaikum and salam satu Malaysia.


This is my first task for today.

09/07/2012

Assalamualaikum and Salam satu Malaysia.

Surface Mount Soldering Procedure

1.  Firstly, apply a little bit of solder lead to one of the PCB pads for the component to be installed.

2. By using a tweezers, pick up the component to be installed and place it over the appropriate pads.

3. At the same time, move the soldering iron to the solder lead on the PCB pad.

4. When the solder lead is heat, use the tweezers to adjust the position of the component.

5. When the position is correct, remove the solder iron and allow the solder lead to cool.

6.  After that, solder on the other side of the PCB pads for component to be install.

7.  Lastly, tidy the soldering as well as the soldering is fulfill like in book Acceptability of Electronic Assemblies (IPC-A-610D) in chapter 4 and chapter 7.

The board that was installed components

2nd Day - 06/07/2012

Assalamualaikum and salam satu Malaysia.

This is a table where students are asked to follow the practical task which is laid out by advisers in the hope that we get a lot better electronic engineering.

TASK	MEMBER	DURATION
MICROCONTROLLER         1. PCB/soldering         2. Sensor-vibrator and                solar         3. Solar + switching         4.  GSM MODEM	Parallel	WEEK 1 – WEEK 4
	BENE
PLC         1. AC/DC, Relay         2. GSM MODEL	Prerequisite	Week 3
	BENT	Week 5
IP CAMERA	BENT               2 person each camera                   *offline(wifi)
MECHANICAL PROTOTYPE PIC/PLC

General Task:
VISUAL BASIC 2010 - WEEK 5

Specific Task:
WEBSITE TEAM

TIMETABLE PRACTICAL ON HIIS EVERYDAY:

9.00AM	In
9.00AM-10.00AM	Report Blog
10.00AM - 12.30PM	Daily Chores
1.00PM-2.00PM	Break
2.00PM-5.00PM	Daily Chores
5.00PM	Dismissed

1st Day - 05/07/2012

Assalamulaikum and Salam satu Malaysia.

05/07/2012

This is my first day in UteM holding. I registered mysellf at 9a.m to Mr. Mazran and Mr Siva at Hitech Integrated Solutions Innovation Sdn. Bhd. located in FKEKK, UTeM.

11 A.M.

Prepared and clean the tutorial room to use it as the company's operations center of HIIS Sdn Bhd as we undertake industrial training. This room will be used as a place to complete task given, such as soldering, update the daily reports on the blog and log books and other tasks.

1 P.M

Dismissed